Ok

En poursuivant votre navigation sur ce site, vous acceptez l'utilisation de cookies. Ces derniers assurent le bon fonctionnement de nos services. En savoir plus.

06/11/2020

Full Process Presentation on Samsung Galaxy S20 Teardown

The Samsung S20 internal structure mainly contains a display screen, middle frame and some small parts. To tear down the Samsung S20, we need to be careful and patient. The first step we would do is take off the battery door, and then off the wireless charging coil. After that we may take off the inside parts which are install on the middle frame. We can disassemble the display screen with middle frame at last and finish the process. Let’s see the details presented below:

 

1. Tear down the battery door and wireless charging port

Power off the phone, eject and take out the SIM card tray. Use hot air gun to blow on the back battery door around the edge. Use suction cup to pull and ultra-thin plastic sheet to slice and separate the battery door. Take off the batter door and then we can see the wireless charging coil on the top. Unbolt the 15 Phillips screws for fixing the charging coil, then we are able to pry and take off the wireless charging coil with steel pry tool from the Samsung phone.

2. Take off the camera module and other small parts

After the charging coil is removed, we can see the flex cable ribbons. Disconnect the battery flex cable firstly. Pry and remove the antenna bracket with spudger on the upside of the phone. After that, we can remove the speaker bracket on the bottom in the same way. Pry and take off the SUB main flex ribbon and antenna flex for connecting the charging port board and mainboard. Unplug the display flex cable. Loosen the screws for fixing the mainboard, and disconnect the front facing camera flex cable. Use spudger to pry and take off the mainboard from the phone. The rear-facing camera module is combined on the mainboard, we can separate the rear cameras form the board. Unbolt the three Phillips screws and take off the Samsung S20 charging port PCB board with spudger. Hot air gun blows and gently pry off the ear speaker from the middle frame.

3. Tear down the battery from the middle frame

After the small parts are taken off from the display, here we can tear down the battery and separate the display screen. Add some battery sticker melted glue and pry the battery off from the middle frame with steel prying tool. Hot air gun blow on the display screen and use ultra-thin sheet to slice and separate the Samsung S20 display screen and digitizer from the frame. All teardown process for Samsung S20 is over.

The whole teardown process will be a little complicated. We suggest you not try if you are not familiar with Samsung S20 repair. The flex ribbons are easy to break, just be care while unplugging. Besides, you may leave comments or email to us if you need any Samsung S20 parts for replacement. Come to Etrade Supply if you are interested in Samsung mobile phone repair.

2e39c8cc-s.jpg

02:50 Publié dans Blog | Lien permanent | Commentaires (0)

23/10/2020

How to Change an iPhone 11 to iPhone 12 by Replacing the Back Housing

The iPhone 12 is launching on the phone market this October. Although it is a time we still have to wait to see this new iPhone module in the flagship store, some of the third-party iPhone 12 back housing has been manufactured. Based on this, we are trying to modify a new iPhone 12 phone by replacing the iPhone 11 parts in the back housing. Let’s check the specific steps below.

 

1. Tear down the iPhone 11 and take off all the inside parts and components

Unbolt the two screws on the button and use a hot air gun to blow on the iPhone 11 display. Use a suction cup and an ultra-thin plastic sheet to slice and separate the display. Flip over the display after it is separated, unbolt the screws and take off the metal shield for fixing the display flex cables. Disconnect and take down the display from the iPhone 11. Take off the taptic engine and the loudspeaker first, then the SIM card tray slot, eject and take out the SIM card beforehand. Disconnect and take off the battery from the iPhone after that. Unbolt the screws and pry out to take off the charging port connector flex, then disconnect and take off the rear-facing cameras and front-facing camera module. Takedown the logic board and bottom flex as well. Take off all the side keys and flex, and the power button flex at last.

2. Assemble all the iPhone 11 parts and components to the iPhone 12 back housing

After all the iPhone 11 inside parts are taken off, here we need to assemble them to the iPhone 12 back housing. Apply the wireless charging coil first on the back housing. Assemble the side key buttons, tighten the screws, and the small metal shield to fix them. Install the dust-proof into the loudspeaker, and then assemble the power button flex. Install the Bluetooth flex, the logic board, and the iPhone 11 rear-facing camera with flex cable onto the back housing, connect the flex cables. Assemble the charging port flex and tighten the screws for fixing it. Install the taptic engine and loudspeaker, connect the flex cables, and fix the cable with a metal shield. Install the SIM card slot and fasten the screws, then install the battery. Don’t forget to past the battery sticker tape on it.

3. Install the iPhone 11 display, turn on the iPhone and test the functions

After all the inside parts are installed, we need to assemble the iPhone 11 display screen on to the iPhone. Apply the water-proof frame sticker on the back housing. Connect the flex cables, place the metal shield, and tighten the screws for fixing it. Insert the SIM card tray into the phone. Assemble the display and make sure it is tightly sealed on the back housing. Turn on the phone and test the functions, such as the screen sensitiveness, the cameras, the Bluetooth connection, the auto-brightness function, the face ID, etc. Make sure all the functions are normal.

 

There is something we have to notice during the process. Some of the iPhone 11 parts and screws are tiny, we need to be careful about classification. Don’t mess them up or miss any part. The flex is easy to break, just be careful while tearing down. In the end, it is recommended to go to Etrade Supply for iPhone 11 replacement parts if you are interested in our modification test. You may leave us a message if you have questions about our products.

24834b66-s.jpg

16/10/2020

How to Fix the iPhone Incoming Calls not Showed on Sleep Mode

The iPhone incoming calls not show when on sleep mode. This issue exists because of the faulty signal baseband component on the logic board. The normal repair solution is taking out the logic board, checking the baseband, and replacing the faulty component. The process would be difficult and complex. Here we can connect a wire from the baseband wake signal point to the WiFi wake signal point to borrow the signal so that the problem would be solved. Check the detailed steps below.   

 

1. Tear down the iPhone screen and take off the logic board

Hot air gun blow on the display, unbolt and take off the two screws on the bottom. Slice and separate the display screen. Disconnect the display flex cables and the battery flex cable, take off the display. Eject and take out the SIM card. Snap and remove the screws, take off the metal panel. Take out the motherboard carefully with tweezers. Fix the motherboard on the PCB motherboard holder. Use a hot air gun to blow on the motherboard and tear off the heat-resistant tape on the back slowly.

 

2. Confirm the signal points and solid tin wire to connect the points

From the Sitemap software on the computer, we can see all the component location and signal points. Confirm the baseband wake signal point location and the WiFi wake signal point location on the software, and then confirm the points on the motherboard. Scratch off the insulating coat from the two points, paste some solder glue on the two points. Solder a tin wire to connect the two points, then coat the wire with a UV solder mask.  

 

3. Install the logic board back to the iPhone and assemble the iPhone

Take off the motherboard from the PCB board after the solder is solidified. Install the motherboard to the iPhone. Connect the iPhone X display screen with flex cables and the battery cable. Insert the SIM card back into the iPhone. Turn on the iPhone and try to call the numbers with another phone. The incoming calls show when the iPhone is on sleep mode. The repair procedure is successful. Turn off the iPhone again. Fix the metal panel and tighten the screws back. Assemble the iPhone. All process is completed.

 

The process above is fast and efficient to solve the iPhone incoming calls not showing on the sleep mode problem. We don’t have to tear down the logic board and check the PMU and baseband CPU. This has saved us a lot of time and work. As a premise, we need to know how to tear down the iPhone X series and replace the iPhone X parts well. Stick on the Etrade Supply blog and you will learn much about iPhone repair.

how to slow iPhone icoming calls not show.jpg

10:25 Publié dans Blog | Lien permanent | Commentaires (0)